BLANCO BRFT7X Bedienungsanleitung Seite 3
- Seite / 10
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
DESCRIPTION
--------------------------------------------------------
The appliance can be used both in Ducting
version and Filtering version.
In the Ducting version (Fig. 1), cooking
vapours and/or odours are conveyed straight
outside (ceiling and/or wall) by a disposal duct,
using the holes that are predisposed on the
top and/or at the back of the apparatus.
In the Filtering version (Fig. 2) cooking
vapours and/or odours are depurated by 2
charcoal filters and recirculated around the
room by the front fissures. ATTENTION: For
the filtering version it is absolutely necessary
to use the charcoal filters whereas for the
ducting version it is not.
INSTALLATION
--------------------------------------------------------
Before assembling the appliance it is necessary
to take off the anti-grease grilles. To take off the
grill it is necessary to push this one towards the
rear of the apparatus, by means of the proper
knobs, so that it gets released, and to rotate it
(Fig. 3); to take it off completely, make it rotate
on one side keeping the other one steady.
Installation in extraction version:
Depending on your requirements, choose
which opening to use for the air outlet (rear or
upper) and fit the flange (A) provided,
proceeding as follows: make the 3 flange tabs
and stop (C) coincide with the slots on the
hood; turn the flange slightly clockwise until it
locks into position (Fig. 4).
On the other opening, fit the cap (B) provided
and make the 3 cap tabs and stop (D) coin-
cide with the slots on the hood; turn the cap
slightly clockwise until it locks into position.
Installation in filter version:
On both the openings (rear and upper), fit the
caps (B) provided, making the 3 cap tabs and
the stop (D) coincide with the slots on the
hood; turn the cap slightly clockwise until it
locks into position.
The following operations are essential for
assembly:
– Install a proper wiring system.
– If your apparatus is to be assembled as a
Ducting appliance, you must first make the
air venting hole and get a proper pipe to
connect the hole to the flange of the hood.
Ducting from the rangehood carrying the
exxhaust air, should not exceed a lenght of
three (3) metres.
For ducted installation we recommend using
galvanised or similar metal type flue pipe. PVC
or other type of plastic materials must not
be used. Ducting must be taken to the outside
of the building and MUST NOT be directed
into a ceiling cavity.
Ducting size should always comply with the
manufacturers specification. The ducting size
should be no less than 125 mm.
Wall fitting
Fig. 5: take 2 of the screws (S) enclosed (the
smallest ones) and partially insert them in the
holes on the telescopic slide (A); do not fix
them completely: they must hold the telescopic
slide. Push the slide back as much as possible
and block it with some adhesive tape (W).
Fix the lower part to the upper part of the
hood by means of the 4 screws supplied (Fig.
5).
Using the drilling template fit 2 of the screw
anchors supplied to the wall (in
correspondence to the holes B (Fig. 6). Insert
two of the screws supplied and hook the
apparatus using the holes B on the rear (Fig.6).
Before fully tightening the screws, mark the
position of the 2 holes C on the wall with a
marking pen. Unhook the hood and drill the 2
holes in the marked positions and insert the
screw anchors. Hook the hood back on and
finally fix it with the 4 screws. Remove the
adhesive tape from the telescopic part and
pull it downwards until it touches the hob.
Make the electrical connection.
Assembly of the telescopic flue (Fig. 7)
Take the bottom bracket (D) and fit the plates
(P) provided in both sides, as shown in Fig.
7 Do the same for the top bracket (E).
Fix the lower bracket (D) onto the apparatus.
Fix the upper bracket (E) onto the ceiling; in
order to position the bracket on the same axis
as your apparatus, refer to the small triangle
(F) that is on the central axis.
Take the two telescopic pipes minding that
you have to lift slightly the smaller pipe (the
upper one); insert the pipes from the front,
expanding slightly with your hands so that
they can get hooked onto the two brackets.
Fix the pipes to the brackets by means of the
screws G and H.
Verwandte Produkte und Handbücher für Nein BLANCO BRFT7X
Nein BLANCO BSO660X Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Nein BLANCO BMS607W Bedienungsanleitung
(23 Seiten)
(23 Seiten)
Nein BLANCO BOST162X Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Nein BLANCO BSO650X Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Nein BLANCO BSO665X Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Nein BLANCO BMS607W Bedienungsanleitung
(23 Seiten)
(23 Seiten)
Nein BLANCO BSO650X Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Nein BLANCO BOSE160X Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Canon Installing Multifunction PIXMA MX340 manuals
Owner’s manuals and user’s guides for Multifunction Devices Canon Installing Multifunction PIXMA MX340.
We providing 1 pdf manuals Canon Installing Multifunction PIXMA MX340 for download free by document types: User Manual
Kommentare zu diesen Handbüchern